This is a cache of https://www.owenscorning.com/en-us/roofing/install-instructions/duraridge. It is a snapshot of the page as it appeared on 2026-02-02T05:17:02.515+0000.
DuraRidge™ Hip & Ridge Shingles Installation Instructions | Owens Corning Roofing
Owens Corning

Before You Begin

Complete shingle application on roof deck before applying hip and ridge shingles. Hip shingles must be applied before applying ridge shingles. All hip and ridge shingles are applied with an 8 inch exposure.

Note: If a new roof is being applied over an existing roof, remove the old hip and ridge shingles to obtain a level application.

Handling: Use extra care in handling shingles when the temperature is below 40°F. In cold weather, it is recommended to warm DURARIDGE shingles before installing.

Fastener Requirement: Use galvanized steel, stainless steel, or aluminum nails minimum 12 gauge shank with 3/8” diameter head. Owens Corning Roofing recommends that fasteners comply with ASTM F 1667. Check local building codes. All Fasteners must penetrate at least 3/4” into the wood deck or completely through sheathing.

Note: Owens Corning Roofing recommends the use of nails as the preferred method of attaching shingles to wood decking or other nailable surface.

Installing

Begin hip application at the eave working toward the ridge.

  1. Begin ridge application opposite the prevailing wind direction. (Fig. A)
  2. Arrange DURARIDGE Hip & Ridge shingles along the center line so that both halves of the laminated piece fall on opposite sides of the hip or ridge. (Fig. B)
  3. Begin application by creating a starting piece using the laminated piece with the 8 inch exposed portion of the shingle removed. Fasten starter piece with one nail on each side 1 inch in from the side edge starting from the fixed side edge placed into the SureNail® Technology fastening area.
  4. Continue to fasten each full shingle through the top laminated piece with one nail on each side placed 9 inches back from the exposed end and 1 inch in from the side edge starting from the fixed edge of each shingle. Note: Fasteners must be placed into the SureNail® Technology fastening area. (Fig. B)
  5. Apply remaining hip and ridge shingles in the same manner with 8 inch exposure.
  6. When finishing the ridge, leave no laminated portion of the last hip and ridge shingle exposed. One option is to use the 8 inch exposure portion of a hip and ridge shingle, cutting a piece the appropriate length to extend over the laminated portion of the shingle to the end of the ridge.
  7. Fasten final piece with two nails, each 1 inch in from each side edge and 1 inch in from the end of the ridge. Cover exposed fasteners with asphalt roof cement. Asphalt roof cement must meet ASTM D-4586 Type I or Type II (Asbestos Free). Note: Please be aware that excessive amounts of asphalt roof cement could blister the shingle.
Fig. A and B

Product Specifications

  • Size: 12 inches x 10 5/8 inches (305 mm x 270 mm)
  • Pieces per Box: 30
  • Application Exposure: 8 inches (203 mm)
  • Lineal Coverage per Box: 20 feet (6.49 m)
  • STORE IN COVERED, VENTILATED AREA (UNDER 110F/43C)
  • DO NOT STACK OVER EIGHT BUNDLES HIGH PER PALLET
  • AVOID OUTSIDE STORAGE WHEN TEMPERATURES EXCEED 90F/32C
  • DO NOT STORE IN DIRECT SUNLIGHT

FAILURE TO FOLLOW THESE STORAGE INSTRUCTIONS COULD CAUSE SHINGLES TO STICK TOGETHER.

Prepared roofing is exempt from OSHA RightTo-Know standard under its provision for articles (29 CFR 1910.1200-b-6-IV) as defined in 29 CFR 1910.1200c

*Limited Lifetime Warranty

This product carries a limited lifetime warranty (for as long as you own your home). You may obtain a copy of this roofing warranty by visiting our website at www.owenscorning.com or call 1-800-GET-PINK® (1-800-438-7465)

Owens Corning Roofing and Asphalt, LLC shall not be responsible for any damage, loss, cost, expense or liability relating to failure to follow these instructions. Failure to follow these installation instructions may affect Owens Corning Roofing and Asphalt, LLC's obligations under this product's limited warranty.

10-YEAR ALGAE-RESISTANCE LIMITED WARRANTY**

**Tropic zones outside of the USA and Canada have a reduced algae resistance limited warranty. See international warranty for more details.

Contact Us

Even though we’re a global company, we’re always ready to answer your questions. Call to speak with an Owens Corning representative.