This is a cache of https://www.owenscorning.com/en-ca/insulation/products/propink-l77-loosefill. It is a snapshot of the page as it appeared on 2026-10-08T05:14:05.492+0000.
PROPINK® Fiberglas® Blown Insulation | Owens Corning Insulation Skip to Main Content

BLOWN LOOSEFILL INSULATION

PROPINK® FIBERGLAS® Blown Loosefill Insulation is an alternative to thermal batt insulation in attics, ceilings and floors for new construction or retrofit applications. Can also be installed within a floor assembly to enhance acoustical properties.

PROPINK® FIBERGLAS® Blown Loosefill Insulation package, Made in Canada seal.

Basic Uses/Related Uses

  • Attics
  • Flat ceilings or ceilings with a maximum slope of 4.5 : 12
  • Floor assemblies
  • Installed with commercial pneumatic equipment

Selection Criteria

  • Will not significantly sag or settle over time, ensuring installed thermal resistance is maintained
  • Non-combustible
  • No weight limit over gypsum sheathing
  • Phenol-formaldehyde, perlite, and vermiculite free
  • Non-corrosive

Certifications and Sustainable Features

  • Recycled content certified by SCS Global services. Current information available at owenscorning.com/en-ca/corporate/sustainability/ product-sustainability/product-transparency-standards; see Recycled Content Certification Canada
  • GREENGUARD Gold Certified products are certified to GREENGUARD standards for low chemical emissions into indoor air during product usage. For more information, visit ul.com/gg
  • UL Environment validated Formaldehyde-Free
  • Product specific Type 3 UL Environmental Product Declaration (EPD) and Transparency Brief certified by UL Environment
  • Participating in Declare- Living Building Challenge Compliant
  • Living Product Challenge Imperative Certified
  • Contributes to credits in green building programs such as LEED® and Green Globes. For further information see documents: LEED® v4 for Building Design and Construction and Owens Corning Impact Study - Leadership in Energy and Environmental Design (LEED® v4).

Technical Information

Performance Criteria

PROPERTY

VALUE

TEST METHOD

COMPLIANCE

CCMC Evaluation Listing No. 12851-L
Type 5

CCMC
CAN/ULC-S702.1 

Additional Performance Information

PROPERTY

VALUE

TEST METHOD

FIRE

Refer to product application chart to achieve
listed thermal resistance values

CAN/ULC-
S702 .1-14-AMD1

Non-CombustibleCAN/ULC-S114

Smoulder Resistance Mean Mass Loss ≤ 0.02%,

CAN/ULC-S129
Flame Spread 0; Smoke Developed 10CAN/ULC-S102.2
MOISTUREFungi Resistance (pass)ASTM C1338

Water Vapour Sorption <5% by weight at 49 °C (120 °F), 95% R.H. 

ASTM C1104

CORROSION

Corrosion of Steel (pass)

C1617

Technical Information

  • Deliver products in their original packages, and store in enclosed shelter.
  • Packaging is not UV resistant. Shelter unused packages from the elements.
  • Stated thermal resistance value is achieved by installing the minimum required number of bags per 92.9 net m2 (1,000 net ft2) at a thickness not less than the label minimum thickness. Failure by the installer to provide both the required number of bags and at least the minimum thickness will result in lower thermal resistance value.
  • Owens Corning does not recommend or approve blending or adding additional materials or adhesives to this product during installation. Owens Corning will accept no responsibility or liability when the product is not installed in accordance with the product label and installation instructions.
  • Building, electrical, fire and other applicable codes shall be complied with. All heat emitting devices, such as fuel burning appliances, chimneys, pipes, ducts and vents to these appliances shall maintain a minimum clearance of 51 mm (2 in.) between these devices and the insulation. Recessed light fixtures, unless designed for the purpose, shall not be installed in insulated ceilings.
  • Ensure applicator's personnel wear protective equipment such as breathing mask (dust-proof type mask), eye protection (safety goggles or eyeglasses), and skin protection (gloves, long-sleeved shirts, and pants) when handling and applying materials. Wash with soap and warm water after handling. Wash work clothes separately and wipe out washer. For additional information refer to Safe Use Instruction Sheet (SUIS) found in the SDS Database via sds.owenscorning.com.
  • When installing PROPINK® FIBERGLAS® Blown Loosefill Insulationin a thermal application, it is critical that the contractor's crews have a general knowledge of construction and framing principles and a full understanding of the pneumatic equipment.
  • Additionally, the following items should be considered:
  • Check for possible routes that may allow insulation to escape from cavities and fall into the condition area.
  • Insulating a cavity that does not have an adequate interior vapour retarder and air barrier substantially increases the potential for moisture problems.
  • Check for cavity surfaces which may not be able to withstand pressures created during the blowing process.
  • Where there are soffit vents, take appropriate measures to prevent blown glass fibre insulation from accumulating and blocking the air ventilation and to prevent the insulation from being displaced due to wind penetration through the soffit vents. Install Owens Corning® raft-R-mate® attic vents.

Technical Services Available

For Canadian Technical inquiries, please contact our technical team at owenscorning.ca/contacttech.


Environmental and Sustainability

Owens Corning is a worldwide leader in building material systems, insulation, and composite solutions, delivering a broad range of high-quality products and services. Owens Corning is committed to driving sustainability by delivering solutions, transforming markets, and enhancing lives. More information can be found at owenscorning.ca or owenscorninglibrary.ca.


Disclaimer of Liability
Technical information contained herein is furnished without charge or obligation and is given and accepted at recipient’s sole risk. Because conditions of use may vary and are beyond our control, Owens Corning makes no representation about and is not responsible or liable for the accuracy or reliability of data associated with particular uses of any product described herein. SCS Global Services provides independent verification of recycled content in building materials and verifies recycled content claims made by manufacturers. For more information, visit SCSglobalservices.com.
LEED® is a registered trademark of the U.S. Green Building Council.

Notes
For additional information, refer to the Safe Use Instruction Sheet (SUIS) found in the SDS Database via sds.owenscorning.com.
Certification logos, Made in Canada seal

Applications

  • Attics
  • Floors
  • Walls

Contact Us

Even though we're a global company, we're always ready to answer your questions. Call to speak with an Owens Corning representative.