This is a cache of https://www.owenscorning.com/en-us/roofing/install-instructions/ventsure-4ft-strip. It is a snapshot of the page as it appeared on 2026-02-06T09:43:29.801+0000.
VentSure® 4-Foot Strip Heat & Moisture Ridge Vents with Weather PROtector® Installation Instructions | Owens Corning Roofing
Owens Corning

VentSure® 4-Foot Strip Ridge Vents are designed for roofs with slopes of ³/12  to 16/12. 

Intake at the eave vents should be equal or exceed that of the ridge vent being installed.


Important Notes

  1. Before applying vent to architectural shingles, leave underlayment long at ridge and fold back under vent or caulk between low areas of shingle and flange of vent, making sure you don’t plug drain holes. This will help prevent wind driven rain and snow from entering the attic.
  2. See instructions for cutting slot.
  3. For structures with different ridge heights, be sure to vent the higher ridge provided there is an opening that connects the two attic spaces.
    It is also acceptable to vent lower ridges with dormers.
  4. For truss roof framing, cut a 1 inch slot on each side of the ridge starting a minimum of 6 inches from the rake edge of the roof.
    For conventionally framed roofs with a center ridge board, cut a 1 inch wide slot beyond the ridge board starting a minimum of 6 inches from the rake edge of the roof. Combined width of slots and ridge board should not exceed 3½ inches.
  5. For best appearance, run VentSure® Ridge Vent from end to end to give the roof a more attractive appearance.

Installation Instructions

Step 1

Using a chalk line, mark out 1 inch on both sides of the ridge as a guide for cutting a slot in the top of the ridge.

Fig. 1

Step 2

Start and end 6 inches away from the rake edge of the roof, cut a slot using a circular saw with the blade set at a depth to cut through the wood sheathing only. Remove the sheathing debris from slot.

Fig. 2

Step 3

Center the vent over the opening that has been cut in the ridge, ensuring the vent sits flat on the roof. Also ensure that the alignment tabs are facing the opposite direction you will be installing the next piece of ridge vent. For cold weather installation leave a gap no bigger than ⅛ inch to allow for expansion. Gaps larger than ⅛ inch could lead to rain and snow entering the attic.

Fig. 3

Step 4

As you install the vents ensure each vent is aligned, then nail in place using the nail holes marked on each vent.

Fig. 4

Step 5

Using a utility knife cut the final piece to a length long enough so that it is flush with the edge of the roof. Connect making sure that the built-in end caps are exposed and nail in place.

Fig. 5

Step 6

Nail hip and ridge shingles over the vent using nails long enough to meet the penetration requirements of the local building code and shingle manufacturer or use nails provided with the VentSure® ridge vent. For a clean look, extend the hip and ridge shingle to cover the alignment tabs or trim tabs off using a utility knife.

Fig. 6

Instructions for Cutting Slots


Hip and Gable Roofs

Cut slot 1 inch on both sides of ridge to within 6 inches of each end wall or hip intersection.


Chimneys

Cut slots 12 inches from chimney. Run ridge vent from end of roof to butt against chimney.


“T” & “L” Roof

Saw slots to within 12 inches of ridge intersection points as shown. Install ridge vent completely across ridge on long side and butt ridge vent on the short run against the side of the long run.

NOTE: To prevent leakage and preserve aesthetic roof line, always leave at least 6 inches between ridge slot and end of ridge.

NOTE: The net free area of soffit ventilation should always be at least equal to or more than the net free area of the ridge ventilation.

Fig. 7–9
NOTE: Owens Corning’s written warranty for this product shall not apply in any instance in which the product was not installed in accordance with the instructions contained herein. See actual warranty for additional warranty details.

LIMITED warranty This product is covered by a Limited warranty which is available by calling 1-800-GET-PINK® or visiting www.owenscorning.com. 

THAT warranty CONSTITUTES OUR EXCLUSIVE warranty, AND WE HEREBY DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL OWENS CORNING BE LIABLE TO CUSTOMER FOR INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES.


Contact Us

Even though we’re a global company, we’re always ready to answer your questions. Call to speak with an Owens Corning representative so you can start your project right away.